Deck preparation
The base is cleared and checked before new layers go down.
Flat Roofing
Rubber Roof Installation Vernon, NJ
A Vernon roofer who installs EPDM can put a new rubber roof on a flat or low slope section of almost any home, and explain each choice before the sheet is rolled out. One call to (973) 858-1840 reaches a nearby rubber roof installer.
A true rubber roof is EPDM, a synthetic rubber membrane used on flat and low slope roofs for decades. The membrane is thick, stretchy rubber that tolerates temperature swings and resists hail and sunlight well. Unlike TPO and PVC, its seams are taped rather than heat welded.
EPDM can be attached in three main ways. Adhered, fastened and ballasted systems each suit different buildings and wind conditions. For homes, adhered EPDM is the most common choice.
Then comes thickness and color. A 60 mil sheet is tougher than 45 mil for roofs that see foot traffic. Black EPDM absorbs heat, which helps in cold climates, while white EPDM reflects sun and keeps rooms below cooler. The transition to a steeper roof or a wall is planned with the same care, since that is where low roofs most often leak.
Depending on what the roofer finds, rubber roof installation in Vernon, NJ can go hand in hand with rubber roof repair and flat roof installation.
Looking for Vernon rubber roof installation? Call (973) 858-1840 and describe the problem to a roofer who works in Vernon.
Call nowThe process
What happens during a rubber roof installation
Each layer is set up to give the membrane a smooth, solid base.
Deck prep
The deck is repaired and checked for slope, ideally a quarter inch per foot toward drains or gutters. Old roofing is removed if the roof is being replaced.
Install insulation
Polyiso insulation and a cover board create a flat, firm base for the rubber. Slope can be built in at this stage.
Sheet layout
Wide sheets are laid out to cover the roof with as few seams as possible, then allowed to relax. Seams are planned so they run with the slope.
Bond the membrane
Bonding adhesive is rolled onto both the cover board and the underside of the rubber, then the sheet is folded back down and broomed smooth. The process repeats for the second half. Brooming from the middle outward pushes trapped air to the edges.
Tape the laps
Laps are primed and joined with seam tape, then rolled to remove air. Lap sealant goes along exposed tape edges.
Flash the details
Walls and curbs get membrane flashing held by termination bar, pipes get pre-molded boots and corners get uncured flashing. The top edge is sealed and covered. Before the crew leaves, seams are probed for any loose spots.
What is included
Parts of a new EPDM roof
Flashing
Termination bar, pipe boots and edge metal are installed to keep water out.
Seam tape
Seams are primed, taped and rolled for a lasting bond.
EPDM membrane
The rubber membrane is adhered or fastened in black or white.
Insulation
Insulation adds energy savings and slope for a smooth surface.
Related service
EPDM Roof Installation Vernon, NJ
EPDM roof installation is straightforward in concept and demanding in the details. The membrane has to lie flat on a clean, dry cover board, the adhesive has to reach the right tack before the sheet is laid and every seam has to be primed and rolled with care. Weather matters too, since adhesives and primers need dry conditions. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
A good Vernon installer also plans for movement. Securing the membrane at the edges and flashing corners correctly prevents later tears. Ask about edge securement before work starts.
Local help
Rubber Roof Installation Near Me
Rubber roofs in Vernon are common on porches, garages, additions and flat sections of older homes. Across Vernon and nearby towns like Hamburg, Highland Lakes, Franklin and Oak Ridge, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, so installation details matter as much as the material.
Need rubber roof installation around Vernon? Call (973) 858-1840 for a Vernon roofer who serves the towns around it too.
Roofs in this climate
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Vernon is busiest after a hard winter and before the next one.
Why call
Why not wait
Less damage
Small roof problems caught early usually stay small repairs.
Local knowledge
Local roofers see the same roofs and storm damage across Vernon and nearby towns.
Straight answers
Ask the roofer about the cause, the options and the estimate before work starts.
Rubber Roof Installation questions
Is it possible to install EPDM over the old roof?
A recover is possible only under certain conditions. The old roof must be a single dry layer, with a recover board over it. If the old roof is wet, it must come off. The roofer tests the old roof for moisture before recommending a recover.
How long does a new rubber roof last?
EPDM can last 25 years or longer. Good seams, drainage and occasional checks make the difference. Repairs are simple when needed.
Is a rubber roof the same as TPO?
EPDM is synthetic rubber, while TPO is a thermoplastic membrane. Black EPDM is taped and stretchy, and white TPO is welded and reflective. Both are common on flat roofs.
How thick should a rubber roof be?
EPDM usually comes in 45 or 60 mil for homes. Sixty mil resists punctures better and lasts longer, which helps on roofs with foot traffic or hail. Thicker 90 mil membrane exists for heavy use.
Should my rubber roof be black or white?
Black and white each have their place. Black holds heat and white reflects it. Talk through the choice with a roofer.
More questions? Call (973) 858-1840
Often needed together
Rubber Roof Repair
EPDM rubber roof repairs done with primer, cover tape and lap sealant made for rubber, so the membrane seals again without a tear-off.
Learn moreFlat Roof Installation
Flat roof installation from the deck and tapered insulation up to the seams, flashing and edge metal, so water drains instead of ponding.
Learn moreTPO Roofing
TPO membrane roofs installed over new insulation or in place of a worn flat roof, built around proper drainage, flashing and edge metal.
Learn moreFlat Roof Replacement
Replacing old built-up, torch-down, EPDM or TPO roofs with a new system built to drain, with tapered insulation where water used to sit.
Learn more
Looking for something else?
See all roofing servicesTalk to a Vernon roofer about rubber roof installation
Call (973) 858-1840 to talk to a roofer serving Vernon, NJ.