Drip edge
Drip edge is added where it was left off with the underlayment lapped correctly.
Roof Repair
Flashing Repair Vernon, NJ
A Vernon roofer can stop leaks where the roof meets a wall, dormer, skylight or edge by renewing the flashing at that joint, with the wall sheathing checked for hidden rot. One call to (973) 858-1840 reaches a nearby roofer who repairs flashing.
Flashing is the thin metal that seals every place the roof surface is interrupted. Step flashing is a series of small bent pieces woven in with each course of shingles along a sidewall, counter flashing laps over it from the wall side, a kickout at the bottom of the wall throws water into the gutter, and drip edge lines the eaves and rakes. When any piece is missing, loose or rusted through, water gets behind the roof covering.
Flashing leaks are sneaky because the water often runs into the wall instead of the attic. A missing kickout is a classic example: water running down the roof edge pours behind the siding at the bottom of the wall, and the rot shows up later as soft trim, stained siding or a damp window below. By the time it is visible, the repair may include some siding and wall sheathing too.
One of the most common shortcuts on roofs is caulk in place of metal. Sealant smeared where flashing should be dries and cracks in a few seasons, and it can trap water instead of shedding it. Lasting flashing repair means new metal installed in the right order, with sealant only as a backup.
Flashing Repair is often paired with chimney flashing repair and roof leak repair, depending on the cause.
Need flashing repair in Vernon? Call (973) 858-1840 to talk to a local roofer.
Call nowThe process
What happens during a flashing repair
Good flashing work is mostly about the order things overlap.
Inspect the joint
The roofer checks the joint from the roof and the attic, looking for missing pieces, rust, face nails and caulk hiding a gap. Damage in the wall changes the scope, so it is checked early.
Expose the old metal
Siding is lifted or removed along the joint so the old flashing and housewrap can be reached. That is the only way to lap new metal behind the wall weather barrier.
Replace the pieces
New step flashing is installed one piece per shingle course, each lapping the one below, with a kickout diverter at the bottom. Nails stay on the horizontal leg, high enough to be covered by the next shingle.
Add counter flashing
Housewrap is lapped over the vertical legs, then siding goes back on with a gap above the shingles so it does not wick water. Siding pressed tight to the shingles stays wet and rots.
Seal the eaves
Damaged drip edge is renewed so water drips clear of the fascia. Correct laps at the edges keep water out of the fascia and soffit.
What is included
Flashing a roofer can repair
Headwall flashing
Headwall metal at the top of a slope is replaced with proper laps over the shingles.
Counter flashing
Counter flashing over step pieces is refitted or replaced so the top edge of the step flashing stays covered.
Step flashing
Sidewall flashing is rebuilt one course at a time so water stays on the roof.
Kickout flashing
Kickouts are fitted at the bottom of roof-to-wall joints so runoff stops soaking the siding.
Related service
Roof Flashing Repair Vernon, NJ
Flashing repairs can be small or involved, depending on how long water has been getting in. Minor work includes refastening loose metal or adding a missing kickout; bigger jobs mean pulling siding and replacing every step piece along a wall. Ask the roofer which kind of repair your joint needs.
Material matters too. Aluminum is common and easy to form, galvanized steel is stiffer, and copper lasts a very long time; aluminum should not sit directly against fresh mortar or certain treated lumber, which can corrode it. Matching metals avoids corrosion where new and old flashing meet.
Related service
Roof Valley Flashing Vernon, NJ
Valleys are the gutters of the roof surface, collecting water from both sides. In an open valley, a band of metal stays exposed down the center, while in a closed or woven valley the shingles cover the valley and the underlayment beneath does the heavy lifting. Both need ice and water shield underneath, centered in the valley.
Leaves and needles that pile up in a valley hold water and wear the shingles or rust the metal. Uncut shingle corners can catch water and direct it under the roofing. Fixing a valley usually involves stripping it, relining it and installing new metal or reshingling.
Local help
Flashing Repair Near Me
In Vernon, many flashing problems date back to an old reroof where the original flashing was reused or caulked instead of replaced. Homes in Vernon and nearby towns like Hamburg, Highland Lakes, Franklin and Oak Ridge range from older houses with aging galvanized flashing and no kickouts to newer homes with complex rooflines that rely on many wall joints, and each of those joints is a place worth checking.
Searching for flashing repair near me from Vernon or Hamburg, Highland Lakes, Franklin and Oak Ridge? Call (973) 858-1840 to talk to a roofer who works in your part of town.
Roofs in this climate
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Vernon, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why act early
Drier ceilings
Small roof problems caught early usually stay small repairs.
Familiar with local homes
Roofers in Vernon know the roof types and weather wear common in local homes.
Clear next steps
Ask your questions before you agree to anything.
Common questions about flashing repair
Can flashing be repaired without replacing the roof?
Flashing repair is a routine job on roofs that are otherwise sound. The work stays local to the joint, with new shingles woven in along it. On an old roof, it may be smarter to plan the flashing with a full replacement.
Why does my roof need kickout flashing?
It is a bent piece of flashing at the lower end of a sidewall joint. It throws runoff away from the wall and into the gutter. Leaving it out is one of the most common causes of rot in the wall under a roof edge.
How do I know if my flashing is leaking?
Look for stains or drips that line up with a roof-to-wall joint. From outside, rusted, loose or caulked-over flashing is a warning sign. Soft or stained siding at the bottom of a sidewall often means a missing kickout. Call (973) 858-1840 to have a roofer check it.
Will caulk fix leaking flashing?
A bead of caulk may hold for a season or two, but it will fail. Sun and temperature swings crack it, and water gets behind it again, sometimes trapped where it rots wood faster. Real repairs use new metal lapped in the right order.
Why does flashing need to be woven with the shingles?
Step flashing is a series of small L-shaped pieces, one for each course of shingles along a wall. Because each piece laps the one below, water is passed down the wall joint from piece to piece and onto the roof. A single long strip of metal along a wall cannot do that and tends to channel water behind the shingles.
More questions? Call (973) 858-1840
Often needed together
Chimney Flashing Repair
Chimney flashing rebuilt so the roof-to-brick joint sheds water again, with a cricket added where the chimney is wide.
Learn moreRoof Leak Repair
Finding where water gets through the roof and sealing it at the source, before wet decking and insulation turn into rot.
Learn moreSkylight Repair
Skylight repair from the flashing on the roof to the glass and the frame, without replacing a unit that can still be saved.
Learn moreRoof Vent Repair
Fixing the vents and pipe collars that poke through a roof and often leak first, before a small crack soaks the attic.
Learn more
Looking for something else?
See all roofing servicesNeed flashing repair in Vernon, NJ?
Call (973) 858-1840 to talk to a roofer serving Vernon, NJ.